⬢This guide will take you through the disassembly and cleaning of the side filament sensor on the Original Prusa XL.
This guide is valid for all versions of the Original Prusa XL and for filament sensors installed on both sides.
JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- このプリンターを使用
- プリンターメンテナンス
- How to clean the side filament sensor (XL)
How to clean the side filament sensor (XL)
Menu
- プリンターメンテナンス
- Packing printer for transport - Original Packing Material (XL)
- Prusaノズル（XLマルチツール）の交換方法
- Packing the XL Multi-tool for return - Original Packing material
- How to fix Modular bed error (HW solution)
- How to replace trapezoid nuts (XL)
- How to replace Nextruder heatsink (XL Multi-tool)
- How to replace the Hotend assembly (XL multi-tool)
- How to replace a profile insert (XL)
- How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
- How to replace the Sandwich Board (XL)
- ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
- How to replace a XY motor (XL)
- How to change the belt (XL)
- How to replace the CoreXY plastic parts
- How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
- How to replace the Prusa Nozzle (XL single-tool)
- How to replace the Hotend assembly (XL single-tool)
- Packing the XL Enclosure for return - Original Packing material
- How to replace a Z-axis motor (XL)
- How to replace a heatbed tile and a heatbed tile cable (XL)
- How to replace a print fan (XL single tool)
- How to clean the side filament sensor (XL)
- 1. Introduction
- 2. Necessary tools
- 3. Printer preparation
- 4. Detaching the side filament sensor
- 5. Disconnecting the filament sensor cable
- 6. Disassembling the side filament sensor
- 7. Accessing and cleaning the mechanism
- 8. Reassembling the filament sensor side
- 9. Reassembling side filament sensor
- 10. Final check
- 11. It's done
- How to change xLCD and xLCD cable (XL single-tool)
- How to replace a Dwarf board (XL multi-tool)
- How to replace a Dwarf board (XL single-tool)
- How to replace a hotend thermistor (XL Single-Tool)
- How to replace a Z-axis linear rail (XL)
- How to replace the hotend fan (XL Multi-tool)
- How to replace a PSU (XL)
- How to replace a hotend heater (XL Single-Tool)
- How to replace the tch-profile-insert (XL)
- How to replace the rubber band on Original Prusa XL (Multi-tool)
- How replace the CoreXY Cover Rear (Original Prusa XL)
- How to change the xLCD (XL)
- How to replace a Nextruder (XL)
How to clean the side filament sensor (XL)
Relevant for:
Last updated a year ago Difficulty
Easy Steps
11 Available languages
⬢For this guide, please prepare:
⬢TX 8 Torx key
⬢Allen key 2.5mm
⬢Compressed air - also known as air duster or canned air
⬢On single-tool XL, unload filament navigating to Filament ->Unload filament.
On multi-tool XL, unload filament from each tool that is attached to the filament sensor assembly.
⬢For each of these tools, navigate to Control ->Pick/Park Tool -> Pick Tool #.
⬢After the tool is picked, navigate to Filament -> Unload filament.
⬢Repeat the unloading procedure for each tool that is attached to the filament sensor assembly.
⬢After all filaments are unloaded, cool down and turn the printer off.
Each of the PTFE tubes on the side filament sensor is secured by a collet, indicated by the blue arrows.
⬢Push on one of the extruder PTFE tube collets.
⬢At the same time gently pull out the extruder PTFE tube from the filament sensor assembly.
⬢Repeat the procedure for the remaining PTFE tubes.
⬢The filament sensor assembly has a hole indicated by the arrow. Inside the hole is a M3x12 screw.
⬢Insert the 2.5mm Allen key in the hole, and loosen the M3x12 screw, to detach the side filament sensor from the rest of the printer.
The connector has a safety latch. It is necessary to press the latch before disconnecting. Otherwise, the connector may get damaged.
⬢Gently press the latch on the connector to disconnect the filament sensor cable.
⬢Loosen the M3x8 screws using the 2.5mm Allen key
⬢Identify a small hole in the filament-sensor-insert
⬢Insert an Allen key in the hole and use it as a lever to push up the filament-sensor-insert.
⬢Using the TX 8, loosen the two M3x10rT screws.
Loosen the screws carefully. Avoid scratching the electronic board with the TX 8.
⬢The mechanism is made of three systems of ball, magnet and spring.
⬢Blow canned air into the spaces where the spring is visible to clean the mechanism.
⬢Using the TX 8, tighten the two M3x10rT screws.
Do not overtighten the screws!
Avoid scratching the electronic board during the procedure.
⬢Push the filament-sensor-insert into the filament-sensor-case
⬢Using the 2.5mm Allen key, tighten the two M3x8 screws.
⬢Plug the filament sensor cable into its connector.
⬢Insert the M3x12 screw using the 2.5mm Allen key through the hole and tighten the screw.
⬢Push each PTFE tube into its slot.
⬢Gently pull each PTFE tube back, this will push out the black collet in the side filament sensor and lock the tube.
⬢For the following step, please prepare a small piece of filament.
⬢Switch the printer on.
⬢On multi-tool XL, navigate to Control ->Pick/Park Tool ->Pick Tool #. Pick one of the tools attached to the affected side filament sensor.
⬢Navigate to Info ->Sensor Info ->Side filament sensor.
⬢From this submenu, the status can be checked. The possible statuses are INS (inserted) and NINS (not inserted).
⬢Insert a piece of filament from the side filament sensor.
⬢Check if the status changes from NINS to INS and vice versa according to the filament insertion.
⬢On multi-tool XL, navigate to Control ->Pick/Park Tool ->Park Current Tool. Repeat the step for each of the tools attached to the same side filament sensor.
⬢That's it, good job! You just successfully cleaned the filament sensor mechanism on your Original Prusa XL.
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.