JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

How to replace a Nextruder (XL)

Menu

How to replace a Nextruder (XL)

How to replace a Nextruder (XL)
Relevant for:
Last updated 10 months ago
How to replace a Nextruder (XL)
 Difficulty
Moderate
 Steps
20
 Available languages
ENCSPLDEESITFR
Introduction
Introduction
This guide will take you through the replacement of the Nextruder on the Original Prusa XL.
Some parts might slightly differ. However, it does not affect the procedure.
必要なパーツは全て弊社eshopで販売しています。shop.prusa3d.com
Note that you have to be logged in to have access to the spare parts section.
Tools necessary for this chapter
Tools necessary for this chapter
Tools necessary for this chapter
For this chapter, please prepare:
Torx TX10 screwdriver
2.5mm Allen key
A cardboard box for use as a heatbed protection during the assembly. Hint: use the Prusament box.
Preparing the printer
Preparing the printer
Preparing the printer
Preparing the printer
Place the empty cardboard box approximately to the front center part of the heatbed.
Manually move the X-axis assembly all the way to the front side of the printer.
Move the extruder approximately to the center of the X-axis.
If you have loaded the filament, unload it from the hotend. On the screen, navigate to Filament -> Unload Filament.
WARNING: The hotend and heatbed are very HOT. Do not touch these parts!!!
Remove fully the filament from the hotend and the PTFE.
Wait till the printer is cold!
Unpluging the printer
Unpluging the printer
Turn the power switch OFF ("O" symbol).
On the rear side of the printer, unplug in the PSU cable.
Disconnecting the extruder
Disconnecting the extruder
Disconnecting the extruder
Disconnecting the extruder
Locate the xl-rear-cable-management-plug (cover) on the rear of the printer.
Slightly loosen the two screws holding the cover. No need to remove them completely. Push the cover to the right and remove it from the printer. Don't throw it away, we'll use it later. 
Disconnect the extruder cable by pushing the security lever on the connector.
Push the black collet to the right.
Pull out the PTFE tube.
Detaching the extruder cable
Detaching the extruder cable
Detaching the extruder cable
PSU側が手前になるようにプリンターを回転させます。
Push the 2,5mm Allen key all the way through a hole in the rear metal sheet as well as through the plastic part until you reach the screw. Untighten the screw.
Take off the xl-dock-cable-router.
Extruder detaching
Extruder detaching
Extruder detaching
Turn the printer so that the LCD is facing you.
Take off the x-carriage-cover from the X-carriage.
With a TX10 screwdriver remove the bottom M3x12bT screws from the X-carriage.
Extruder take off
Extruder take off
Extruder take off
Hold the extruder during detaching.
Hold the extruder and with a TX10 screwdriver unscrew two M3x12bT screws.
Take off the extruder assembly from the X-carriage
Preparing the new Nextruder
Preparing the new Nextruder
Preparing the new Nextruder
For the following steps, please prepare:
ネクストルーダーケーブルアセンブリ(1本)
Nextruder (1x)
これが次のステップでネクストルーダーに取り付けるケーブル束の端です。ケーブルコネクター、フレキシブルプレート、半透明のPTFEチューブで構成されています。
Nextruder cable & PTFE tube
Nextruder cable & PTFE tube
Nextruder cable & PTFE tube
Nextruder cable & PTFE tube
Using the T10 screwdriver, loosen the marked two screws on the inside of the nextruder.
Hook up the keyhole openings in the flexible plate of the cable bundle onto the screw heads.
写真のように、ケーブルとコネクターがある束の部分がエクストルーダーの上部を向いていることを確認します。
Using a T10 screwdriver, tighten marked two screws on the inside of the extruder.
ケーブル・バンドルは、写真と全く同じように、ケーブルが上に、半透明のPTFEチューブが下になるように取り付ける必要があります。
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Pull the flexible line up so that the screws engage into the narrower part of the keyhole openings.
両方のネジがかみ合っていることを確認します。
While the screws sit in the narrower parts of the openings, tighten them up using the T10 screwdriver.
ケーブル束のフレキシブルな部分がエクストルーダー本体にしっかりと固定されていることを確認します。
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Nextruder cable bundle assembly
ケーブルコネクターをネクストルーダーの上部に取り付けます。
Insert the semi-transparent PTFE tube into the fitting on the extruder. Push it all the way in.
Good! Your nextruder assembly is ready to be installed.
エクストルーダーの取り付け:部品の準備
エクストルーダーの取り付け:部品の準備
エクストルーダーの取り付け:部品の準備
エクストルーダーの取り付け:部品の準備
For the following steps, please prepare:
シングルツールエクストルーダーアセンブリ (1個)
各プリンターは出荷前に入念なテストを行っているため、エクストルーダーのノズルに小さなフィラメントが残っている場合があります。
From the extruder body, remove four M3x12bT (countersunk) screws and set them aside. You will need them in the next step.
Installing the extruder
Installing the extruder
Installing the extruder
Atach the extruder assembly to the X-carriage. See the correct orientation of the extruder.
Hold the extruder during installation.
Hold the extruder in place and secure it using two M3x12bT screws in the top two openings. Do not fully tighten the screws yet!
Securing the extruder
Securing the extruder
Securing the extruder
Securing the extruder
Add the two remaining M3x12bT screws into the lower openings in the X-carriage to fix the extruder assembly in place. Do not fully tighten the screws yet!
Tighten all four screws in a diagonal pattern to secure the extruder assembly.
Attach the x-carriage-cover onto the X-carriage. Press it in unti it clicks in.
Remove the Prusament cardboard box off the heatbed.
エクストルーダーケーブルの取り付け
エクストルーダーケーブルの取り付け
エクストルーダーケーブルの取り付け
エクストルーダーケーブルの取り付け
PSU側が手前になるようにプリンターを回転させます。
上面の押し出し材の背面にある長い金属製プロファイル(tch-mounting-insert)を探します。そこに5つのネジ穴があります。
Place the xl-dock-cable-router (the plastic part) between the rear metal sheet and the aluminum extrusion.
There is a screw protruding from the xl-dock-cable-router. The screw must be attached to the third threaded opening on the long metal profile. Look through the rear metal sheet to check if the cable holder is lined up with the correct opening.
Push the Allen key all the way through a hole (bottom left in the pattern) in the rear metal sheet as well as through the plastic part until you reach the screw. Tighten it up.
エクストルーダーケーブルの接続
エクストルーダーケーブルの接続
エクストルーダーケーブルの接続
Locate the xl-rear-cable-management-plug (cover) on the rear of the printer.
Connect the extruder cable into the upper connector labeled DWARF 1.
Re-attach the cover onto the screws. Push it all the way to the left and tighten the screws back up.
Well done!
Well done!
Good job! You made it!
Now you need to go through the printer self-test and calibration. Use chapter First run from the printer assembly instructions.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us