⬢Loosen two screws on the xl-rear-cable-management-plug slightly and push the cover to the side or remove them completely along with the cover to get better access.

⬢Remove the two M3x5rT screws using a T10 screwdriver. Do so also on the other side.

⬢Loosen (or remove) the four screws.

⬢Remove the XL-buddy-box-cover.

⬢Disconnect the extruder cable.

⬢Remove the Rear-cable-management-upper electronics cover.

⬢Gently disconnect the LCD cable.

⬢Cut the two zip ties holding the cables and leave the xLCD cables hanging.

⬢Remove the plastic cable cover from the vertical extrusion and carefully pull out the xLCD cables.

⬢Remove the M3x10 screw.

⬢Remove the frame-rear-cover.

⬢Remove the M3x12rT screw by using a T10 screwdriver and remove the filament sensor (leave it hanging on its cable).

⬢Loosen the M5x85 screw and remove the spool holder.

⬢Place the printer on its side.

Make sure the filament sensor doesn't get crushed or its cable pinched while laying the printer.

⬢While the printer is laying on its left side, remove the extrusion cover to further release the xLCD cables.

⬢Remove the Z-motor-cable-bottom-cover.

⬢Remove the 182mm extrusion cover.

⬢Remove the xLCD-cable-bottom-cover.

⬢Remove the extrusion cover 172 mm.

⬢Remove the xLCD-cable-bottom-holder.

Continue carefully pulling out the xLCD cable while keeping the grounding cable and the right Z-axis motor cable inside the extrusion.

⬢Disconnect the xLCD cable from the xLCD unit.

Gently pull the cable while slightly wiggling to disconnect them.

⬢Remove the M3x16 screw in the right (now the top) xLCD support.

⬢Remove the M3x16 screw in the left (now the bottom) xLCD support and remove the xLCD unit.

⬢Disconnect the xLCD PE cable from the xLCD unit:

Gently pull the cable while slightly wiggling to disconnect them.

⬢Remove the five M3x8 screws and take off the right plastic support.

⬢Take off the left plastic support by turning it upwards in order to lift the xLCD out of its printed housing.

⬢Remove the xLCD button's printed knob and carefully push onto the button while holding the plastic housing to separate the xLCD from its housing.

For the following steps, please prepare:

⬢Left xLCD support (1x)

⬢Right xLCD support (1x)

⬢xLCD cover (1x)

⬢M3x8 screw (5x)

⬢M3x16 screw (2x)

⬢xLCD unit (1x)

⬢xLCD cable (1x)

The list continues in the next step...

⬢Frame-rear-cover (1x)

⬢xLCD-cable-bottom-cover (1x)

⬢xLCD-cable-bottom-holder (1x)

⬢Z-motor-cable-bottom-cover (1x)

⬢Extrusion cover 172 mm (1x)

⬢Extrusion cover 182 mm (1x)

⬢Extrusion cover 243 mm (2x)

⬢Insert the xLCD unit into the xLCD cover.

⬢Notice a little latch on the left xLCD support. Insert this latch in between the xLCD unit and the xLCD cover.

⬢Flip the left xLCD support onto the xLCD unit while keeping the latch in place.

⬢Mount the right xLCD support and secure both xLCD supports with five M3x8 screws.

⬢Locate the M3nEs nuts in the front base extrusion and place the xLCD assembly in front of it.

⬢Insert the M3x16 screw into the right xLCD support.

⬢Use the 2.5mm Allen key to tighten the M3x16 screw into the M3nEs nut in the frame.

⬢Insert the second M3x16 screw from the left side and tighten it, but not overtighten. We will adjust the correct position of the xLCD assembly later on.

⬢Version A: faston on the bottom right

⬢Version B: faston on the top left

Take a closer look at the rear side of the xLCD assembly and locate the PE Faston on the xLCD board. Slide the PE cable connector all the way onto the PE Faston.

⬢Version A

⬢Version B

⬢Connect the xLCD cable to the xLCD slot on the board.

⬢Make sure, that cable is not twisted.

⬢Insert the xLCD cable into the frame, copy the line of the PE cable, and cover the PE cable.

⬢Guide all xLCD cables as close to corner as possible.

Once in the corner flip the cables along the upper edge. See the picture.

⬢Insert the xLCD-cable-bottom-holder into the frame.

⬢Gently insert the xLCD-cable-bottom-cover into the vertical frame.

⬢Insert the Extrusion cover 172mm to the frame and push it up to the xLCD-cable-bottom-cover.

⬢Fully insert the Extrusion cover 172 mm into the frame.

⬢Take the xLCD and PE cables and gently push them up.

Make sure the cable loop is not too large.

⬢Guide the xLCD and the PE cables through the extrusion.

⬢Insert the Z motor cable into the extrusion.

⬢Guide the cables together through the extrusion, as in the picture.

⬢Insert the 182mm extrusion cover into the extrusion.

⬢Push the extrusion cover to the left side.

⬢Fully insert the 182mm extrusion cover right next to the corner-frame-cover.

⬢Push the Z-motor-cable-bottom-cover into the frame.

⬢Gently bend the cables over the corner and insert them into the extrusion. Start with the Z motor cable and then proceed with xLCD and PE cables. Gently bend the xLCD cable over the corner and insert it in the extrusion.

⬢Attach the frame-rear-cover on the printer. Make sure it perfectly fits on the extrusions.

⬢Secure it with the M3x10 screw.

⬢Insert the Extrusion cover 243mm.

⬢Lead the xLCD cable all the way up  the vertical metal extrusion.

⬢Secure the cables with the Extrusion cover 354 mm.

⬢Connect the xLCD cable.

⬢Insert two zip ties through the perforations in the metal sheet to secure the cables. Tighten them gently.

⬢Cut the excess of the zip ties.

⬢Gently attach the Rear-cable-management-upper on the rear side.

⬢Secure it with four M3x5rT screws using a T10 screwdriver.

⬢Connect the extruder cable.

⬢Put the XL-buddy-box-cover back on the printer.

⬢With a T10 key tighten the four screws.

⬢Mount the xl-rear-cable-management-plug and tighten its two M3x5rT screws using a T10 screwdriver.

⬢To the printer's side where you previously removed the filament sensor and the spool holder from, mount the filament sensor and secure it with the M3x12rT screw by using a T10 screwdriver.

⬢Mount the spool holder and secure it with the M5x85 screw.