⬢Move the Heatbed all the way to the top
menu -> control -> move axis -> move Z
⬢Turn the power switch OFF (symbol "O").
⬢From the rear side of the printer, unplug the PSU cable.
EN
Login- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- Using the printer
- Printer maintenance
- How to fix Modular bed error (HW solution)
How to fix Modular bed error (HW solution)
Menu
- Printer maintenance
- Packing printer for transport - Original Packing Material (XL)
- How to replace the Prusa Nozzle (XL multi-tool)
- Packing the XL Multi-tool for return - Original Packing material
- How to fix Modular bed error (HW solution)
- 1. Preparing the printer
- 2. Parts preparation
- 3. Disassembling the Heatbed parts
- 4. Assembling replacement parts
- 5. Assembling the Heatbed parts
- 6. Final assembly
- How to replace trapezoid nuts (XL)
- How to replace Nextruder heatsink (XL Multi-tool)
- How to replace the Hotend assembly (XL multi-tool)
- How to replace a profile insert (XL)
- How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
- How to replace the Sandwich Board (XL)
- How to install the Nextruder V6 Nozzle Adapter (XL Multi-Tool)
- How to replace a XY motor (XL)
- How to change the belt (XL)
- How to replace the CoreXY plastic parts
- How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
- How to replace the Prusa Nozzle (XL single-tool)
- How to replace the Hotend assembly (XL single-tool)
- Packing the XL Enclosure for return - Original Packing material
- How to replace a Z-axis motor (XL)
- How to replace a heatbed tile and a heatbed tile cable (XL)
- How to replace a print fan (XL single tool)
- How to clean the side filament sensor (XL)
- How to change xLCD and xLCD cable (XL single-tool)
- How to replace a Dwarf board (XL multi-tool)
- How to replace a Dwarf board (XL single-tool)
- How to replace a hotend thermistor (XL Single-Tool)
- How to replace a Z-axis linear rail (XL)
- How to replace the hotend fan (XL Multi-tool)
- How to replace a PSU (XL)
- How to replace a hotend heater (XL Single-Tool)
- How to replace the tch-profile-insert (XL)
- How to replace the rubber band on Original Prusa XL (Multi-tool)
- How replace the CoreXY Cover Rear (Original Prusa XL)
- How to change the xLCD (XL)
- How to replace a Nextruder (XL)
How to fix Modular bed error (HW solution)
Relevant for:
Last updated a year ago Difficulty
Very easy Steps
6 Available languages
⬢Unscrew four M3x16 screws and remove the cover.
⬢Unscrew four M3x10tx screws and remove them.
Be careful around the electronics
The heatbed board will be held by cables.
⬢Remove the XL-bed-controller-mount-rear-E2 (plastic part) from the top of the board.
Remove the two M3nE nuts from the old part XL-bed-controller-mount-rear-E2.
⬢Add two M3nE nuts to the new plastic part (XL-bed-controller-mount-rear-E3).
⬢Place the Modular Bed PCB Shield on the XL-bed-controller-mount-rear-E3.
The parts are not fixed together.
⬢Put the plastic part with the metal part on the bottom face of the electronic board.
⬢XL-bed-controller-mount-rear-E3
⬢Modular Bed PCB Shield
The Modular Bed PCB Shield should be on the top of the plastic part
The plastic and metal parts are not attached to each other. You have to hold the parts.
⬢Attach the board back on the heatbed. Secure the board with four M3x10t screws.
⬢Attach the electronic cover back and secure four M3x16 screws.
⬢Well done!
Perform a self-test after assembly is done.
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.