JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- キャリブレーション
- キャリブレーションエラーメッセージ
- Wizard data failure #10526 (SL1/SL1S)
Wizard data failure #10526 (SL1/SL1S)
Menu
- 基本的なキャリブレーション
- 高度なキャリブレーション
- キャリブレーションエラーメッセージ
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- X/Y/Z各軸の長さの確認 (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- ノズル先端からベッド面までの距離がまだ設定されていません
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- プリンタがまだキャリブレーションされていません
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QRエラーコード
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- 静的メモリが上書きされました
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- What happened?
- How to fix it?
- Guides
- XYZ Calibration error-messages (MK2/S)
- XYZキャリブレーション・エラーメッセージ(MK3/MK3S/MK3S+)
This article is also available in following languages: 
What happened?
The printer is displaying the message: Failed to save Wizard data. Restart the printer and try again.
Error name: Wizard data failure
Error code: #10526
How to fix it?
Try to restart the printer and run the Wizard again. If it persists, please update the firmware of the printer.
Guides
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.