JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- キャリブレーション
- キャリブレーションエラーメッセージ
- Calibration error #10113 (SL1/SL1S)
Calibration error #10113 (SL1/SL1S)
Menu
- 基本的なキャリブレーション
- 高度なキャリブレーション
- キャリブレーションエラーメッセージ
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- What happened?
- How to fix it?
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- X/Y/Z各軸の長さの確認 (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- ノズル先端からベッド面までの距離がまだ設定されていません
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- プリンタがまだキャリブレーションされていません
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QRエラーコード
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- 静的メモリが上書きされました
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- XYZ Calibration error-messages (MK2/S)
- XYZキャリブレーション・エラーメッセージ(MK3/MK3S/MK3S+)
This article is also available in following languages: 
What happened?
The printer is displaying the message: The printer is not calibrated. Please run the Wizard first.
Error name: Not mechanically calibrated
Error code: #10113
Issued when the printer has not been calibrated before a print.
How to fix it?
Go in the printer menu to LCD menu -> Settings -> Calibration -> Printer Calibration. Follow the instructions on the screen, and remember that you can swipe the screen to see example pictures of each step of the calibration.
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.