EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

8. Spool holder Assembly

8. Spool holder Assembly

8. Spool holder Assembly
Relevant for:
Last updated 2 months ago
8. Spool holder Assembly
 Difficulty
Easy
 Steps
16
 Available languages
CSPLDEESITFR
Two Spoolholder types
Two Spoolholder types

In this chapter, we will assemble the spoolholders, but before we proceed, note there are two types of the spoolholder.

Inspect the box your kit came in. If the large portion of the box is occupied by the rectangular black trays, you have the first version, the older vacuum-formed spoolholders.

1. Classic vacuum-formed spoolholder

If you have this version, continue to the following step Vacuum formed holder parts preparation
2. New injection-molded spoolholder
This version comes in five packages inside a smaller box. If you have this version, skip to Injection molded spoolholder: parts preparation
Foam pads installation
Foam pads installation
Foam pads installation
Turn the spoolholder base upside down.
Peel off the yellow protective layer off the foam pads.
Attach the four foam pads into the bottom corners of the spoolholder base.
Rods and bearings assembly
Rods and bearings assembly
Rods and bearings assembly
Rods and bearings assembly
Attach a bearing onto each end of both rods.
Attach the plugs onto the rod ends to fix the bearings on each rod.
Finishing up the Spoolholders (vac. form.)
Finishing up the Spoolholders (vac. form.)
Finishing up the Spoolholders (vac. form.)
Finishing up the Spoolholders (vac. form.)
Attach the rods with bearings into the base part so that the bearings engage into the corresponding grooves on the base.
There is a notch on the front part of the spoolholder.
Attach the PTFE holder onto the notched front part of the spoolholder.
Repeat the same steps to build the remaining spool holders until you finish all five.
Injection molded holder parts preparation
Injection molded holder parts preparation
For the following steps, please prepare:
Spool holder Base (4x)
Spool holder Guide (1x)
Spool holder Wheel (4x)
Wheels shipped after April 2024 are made of POM. We recommend using this version over the earlier models made from ABS.
sheet of Foam Pads (1x)
PTFE holder (1x)
Base assembly (part 1)
Base assembly (part 1)
Base assembly (part 1)
Base assembly (part 1)
Take one Base part. Arrange it as seen in the picture.
Insert two wheels into the Base.
Cover the assembly with another Base part on top.
Base assembly (part 2)
Base assembly (part 2)
Base assembly (part 2)
Push both Base parts together until they fully engage one into the other.
Verify the Base parts hold together properly.
Repeat the same steps for the other side part of the spool holder, until you get two of these.
Foam pads installation (part 1)
Foam pads installation (part 1)
Foam pads installation (part 1)
Foam pads installation (part 1)
Take the foam pad sheet. Bend it to separate the individual foam pad strips.
There is a bending line inside the inner opening on the bottom of the spoolholder side part.
Attach an individual foam pad strip onto the middle of the bending line inside the opening, as seen in the picture.
Foam pads installation (part 2)
Foam pads installation (part 2)
Foam pads installation (part 2)
Attach another four foam pad strips onto the marked positions on the bottom of the spool holder side part.
Install another six foam pad strips onto the other side part of the spool holder.
PTFE holder assembly
PTFE holder assembly
PTFE holder assembly
PTFE holder assembly
Take the spoolholder Guide part. Hook the end of the PTFE holder onto the Guide
Make sure the longer part of the PTFE holder is located at the narrower side of the Guide part.
Push the PTFE holder down onto the Guide until it fully engages and locks in place.
Finishing up the Spoolholders (inj. mol.)
Finishing up the Spoolholders (inj. mol.)
Finishing up the Spoolholders (inj. mol.)
Slide the side parts onto the Guide part.

Repeat the same steps for the remaining Spool holders, until you assemble all five.

(Don't forget about the foam pads on the bottom!)

Joining the Spoolholder Guides
Joining the Spoolholder Guides
Joining the Spoolholder Guides
Joining the Spoolholder Guides

There are protrusions on each side of the Guide part.

Using these protrusions, the Guide parts can be joined together. To join them together, simply tilt in the Guide parts one into the other until the protrusions click in.
The Guides can be joined together in form of a straight line.
Or, if you flip one of the Guides around, they can be joined in an arc pattern. This is handy to form an arc of spool holders around the Buffer so that each filament path is as straight as possible.
Continue
Continue
Continue
If you’re installing the MMU3 on an MK4/S printer, move to the chapter:
If you’re installing the MMU3 on an MK3S+ or MK3.5/S printer, move to the chapter:
In these chapters, we will convert the single-material extruder into the MMU3 version.
If you’re doing the MMU2S to MMU3 Upgrade on MK3S+, continue to the chapter:
This chapter will take you through the MMU2S Extruder to MMU3 Extruder upgrade.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us