CS
  • English
  • Italiano
  • Deutsch
  • Français
Přihlásit

How to replace the door (HT90)

Menu

How to replace the door (HT90)

How to replace the door (HT90)
Relevantní pro:
HT90
Poslední aktualizace 2 days ago
How to replace the door (HT90)
 Obtížnost
Střední
 Kroky
16
 Dostupné překlady
ENDEITFR

Krok 1 Introduction

Introduction
Introduction
⬢This guide will take you through the replacement of the door panel on the Prusa Pro HT90.
CAUTION: Handle the Printer and Its Components with Care!
The printer is heavy. Seek assistance to lift or move it and avoid injury or damage safely.
Žádné díly nevyhazujte, pokud k tomu nedostanete pokyn.

Krok 3 Door opening stopper releasing

Door opening stopper releasing
Door opening stopper releasing
Door opening stopper releasing
⬢Open the lid.
⬢Using a flat screwdriver, loosen and remove the Door-opening-stopper by turning it 120° counter-clockwise.
The Door-opening-stopper is a printed part, just a slight twist will loosen this part.
⬢Pokračujte k dalšímu kroku.

Krok 4 Door opening stopper removing

Door opening stopper removing
Door opening stopper removing
Door opening stopper removing
⬢Remove the Door-opening-stopper by pushing from the inside of the printer.
⬢Repeat the process on the second Door-opening-stopper on the other side of the lid.

Krok 5 Releasing the spring rod

Releasing the spring rod
Releasing the spring rod
Releasing the spring rod
Releasing the spring rod
⬢Press the handle lever to the middle position.
⬢Maintain the handle lever in this position.
⬢From the inside of the printer, pull the spring rod out of the handle.
If the spring rod cannot be pulled out, try a different lever position.
⬢Slide the Spring rod out of the Spring Guide on both sides of the door.
The rod can be bent quite a lot to remove it carefully.
⬢Remove the Spring rod from the printer.

Krok 6 Releasing the Spring Gudies

Releasing the Spring Gudies
Releasing the Spring Gudies
Releasing the Spring Gudies
Releasing the Spring Gudies
⬢Release and remove two M3x12r screws with the plastic pad from the right side of the door.
⬢Release and remove two M3x12r screws with the plastic pad from the left side of the door.
⬢Carefully slide the door upwards.
⬢You will have two plastic parts left in place: Spring Guides.
It is important to keep the position of the left and right sides. Do not replace them for later reassembly.
Doporučujeme je ponechat na místě po celou dobu postupu.

Krok 7 Removing the handle

Removing the handle
Removing the handle
Removing the handle
Removing the handle
⬢From the inside of the printer, remove two M3x12 screw securing the handle.
⬢Remove the handle assembly from the printer.
After removing the handle, check that it has two black parts.
⬢The two black parts must be aligned with the handle's surface.

Krok 8 Odstranění panelu dvířek

Odstranění panelu dvířek
Odstranění panelu dvířek
⬢Very carefully slide the door panel up completely out of the printer.
⬢Put this door panel aside, you will no longer need it.

Krok 9 New door panel: parts preparation

New door panel: parts preparation
New door panel: parts preparation
New door panel: parts preparation
New door panel: parts preparation
⬢Pro následující kroky si prosím připravte:
⬢New door panel (1x)
⬢Door-opening-stopper (2x) you removed earlier
⬢Door handle assembly (1x) you removed earlier
⬢M3x12 screw (2x) you removed earlier
⬢M3 washer (2x) you removed earlier

Krok 10 Zavření víka

Zavření víka
Zavření víka
Zavření víka
Zavření víka
Before pulling down the lid, check that the plastic Door-guide on both sides are inserted into the rails. See at the picture.
⬢Now slowly pull the lid downwards until the plastic cut-outs for the Door-opening-stopper are under the top panel. See the picture.

Krok 11 Door opening stopper securing

Door opening stopper securing
Door opening stopper securing
Door opening stopper securing
Door opening stopper securing
⬢Using a flat screwdriver, secure the Door-opening-stopper by turning it clockwise.
The Door-opening-stopper is a printed part, just a slight twist will secure this part.
⬢Repeat this proces on the left side of the lid.
⬢V dalším kroku si připravte dva šrouby M3x12 a na každý z nich nasaďte podložku M3.

Krok 12 Montáž držáku

Montáž držáku
Montáž držáku
Montáž držáku
Montáž držáku
Ensure that both black plastic parts are securely positioned in the handle.
⬢The two black parts must be perfectly flush with the handle’s surface.
⬢Attach the handle to the door. Ensure the correct position of the part.
⬢Z předchozího kroku si připravte dva šrouby M3x12 s již namontovanými podložkami M3.
⬢From the inside of the printer, secure the handle using two M3x12 screw with M3 washers.
Šrouby příliš neutahujte, mohlo by to poškodit panel dvířek.

Krok 13 Spring guides: parts preparation

Spring guides: parts preparation
Spring guides: parts preparation
Spring guides: parts preparation
Spring guides: parts preparation
⬢Pro následující kroky si prosím připravte:
⬢Spring-guide-left (1x) you removed earlier
⬢Spring-guide-right (1x) you removed earlier
Tyto části nejsou identické; jsou zrcadlově obrácené. Pečlivě si prohlédněte obrázek a určete levou a pravou část.
⬢M3x12r screw (4x) you removed earlier
⬢Screw-pad (2x) you removed earlier
⬢Spring Rod assembly (1x) you removed earlier
⬢Prázdná kartonová krabice např. box od Prusamentu

Krok 14 Installing the Spring Guides

Installing the Spring Guides
Installing the Spring Guides
Installing the Spring Guides
Installing the Spring Guides
⬢Lift the door up.
⬢Place the cardboard box on its side beneath the door to provide better access to the printer. And put the door on the box.
⬢Make sure both Spring Guides are still in place.
⬢From the inside, attach the Spring-guide-left to the holes in the door panel. The side of the part without the "pocket" must point upwards.
⬢Line up the holes of both parts and secure it with two M3x12r screws and Screw-pad.
Šrouby příliš neutahujte, mohlo by to poškodit panel dvířek.
⬢Stejný postup použijte u Spring-guide-right.

Krok 15 Inserting the Spring rod

Inserting the Spring rod
Inserting the Spring rod
Inserting the Spring rod
Inserting the Spring rod
⬢Insert one end of the Spring Rod into the left Spring-guide-left.
To insert, the rod must be bent slightly. Don't worry, it is flexible and its shape will return to its original state.
⬢In the same way, insert the rod to the Spring-guide-right.
⬢Push the handle lever to the middle position and insert the center part of the Spring Rod into the handle hook.
⬢Zkontrolujte, zda je tyč správně usazena. (pohled zevnitř)
The rod must be seated at the bottom of the hook.

Krok 16 A je to!

A je to!
A je to!
⬢Remove the cardboard box.
⬢To test that everything is installed correctly, try extending the door to more than one position.
⬢Everything’s fine? Congratulations! You’ve successfully replaced the HT90 door assembly.
Byl tento návod užitečný?

Komentáře

Stále nemáte jasno?

Stále nemáte jasno?

Pokud nemůžete najít odpověď na vaši otázku, projděte si naše další materiály na webu.
A pokud nenajdete odpověď, pošlete nám zprávu na [email protected] nebo přes tlačítko níže.

Kontaktujte nás