IT
  • English
Login

LCD menu (MK3.5/S)

Menu
Rilevante per:
MK3.5MK3.5S
Ultimo aggiornamento a day ago
Questo articolo è disponibile anche nelle seguenti lingue: 
EN

The Original Prusa MK3.5S is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Make sure always to have the latest firmware.
  • Tune
      • Live Adjust Z
      • Change Filament
      • Cancel Object
          • Cancel Current
      • Print Speed
      • Nozzle Temperature
      • Heatbed Temperature
      • Print Fan Speed
      • Flow Factor
      • Filament Sensor
      • Stealth Mode
      • Sound Mode [Loud/Silent/Assist/Once]
      • Input Shaper
          • Calibration
          • X-axis filter
          • X-axis frequency
          • Y-axis filter
          • Y-axis frequency
          • Restore defaults
      • Fan Check
      • Verify Gcode
      • Cutter (Only Available when MMU is installed)
      • User Interface
          • Footer
          • Sort Files [Time/Name]
          • Print Progress Screen [OFF, 30 s - 200 s]
          • Menu Timeout
          • Sound Mode [Loud/Silent/Assist/Once]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • RGB Status Bar
          • Touch
          • Touch Sig workaround
      • Network
          • Active Interface [Eth/Wi-fi]
          • Network status
              • Wi-fi status
              • IPv4 Address
              • IPv4 Gateway
              • MAC Address
              • Hostname
              • DNS Server
              • Connect Host
              • Connect IP
              • Ping | Loss
                • Connect
                • Gateway
                • DNS server
          • Wi-Fi
              • Wi-Fi status
              • SSID
              • Wi-Fi Wizard
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
          • Ethernet
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
          • Prusa Connect
              • Enabled
              • Status
              • Error
              • Hostname
              • Add printer to Connect
              • Load Settings
          • Prusa Link
              • Enabled
              • User
              • Password
              • IPv4 address
              • Hostname
              • Generate Password
          • Metrics & Log
              • What is this?
              • Allow
              • Enable Stored on Startup
              • Stored configuration
                • Host
                • Metrics port
                • Log Port
              • Current configuration
                • Metrics Host
                • Metrics Port
                • Log Host
                • Log Port
      • Time Zone Hour Offset
      • Time Zone Minute Offset
      • Time Zone Summertime
      • Info
      • Message History
  • Pause
  • Stop
  • Print
  • Preheat
      • PLA
      • PETG
      • ASA
      • PC
      • PVB
      • ABS
      • HIPS
      • PP
      • FLEX
      • PA
      • Cooldown
  • Filament
      • Load filament
      • Unload filament
      • Change filament
      • Purge filament
      • Preload to MMU (Only Available when MMU is installed)
          • Preload All
          • Preload Filament 1
          • Preload Filament 2
          • Preload Filament 3
          • Preload Filament 4
          • Preload Filament 5
      • Preload to MMU Advanced (Only Available when MMU is installed)
          • Filament 1 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
          • Filament 2 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
          • Filament 3 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
          • Filament 4 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
          • Filament 5 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
          • Carry Out the Changes
      • Load to Nozzle (Only Available when MMU is installed)
          • Load Filament 1
          • Load Filament 2
          • Load Filament 3
          • Load Filament 4
          • Load Filament 5
      • Unload Filament (Only Available when MMU is installed)
          • PLA
          • PETG
          • ASA
          • PC
          • PVB
          • ABS
          • HIPS
          • PP
          • FLEX
          • PA
      • Eject From MMU (Only Available when MMU is installed)
          • Eject From MMU 1
          • Eject From MMU 2
          • Eject From MMU 3
          • Eject From MMU 4
          • Eject From MMU 5
      • Cut Filament (Only Available when MMU is installed)
          • Cut Filament 1
          • Cut Filament 2
          • Cut Filament 3
          • Cut Filament 4
          • Cut Filament 5
          • Manage Filaments (Only Available when MMU is installed)
  • Control
      • Move axis
          • Move X
          • Move Y
          • Move Z
          • Move E
          • Cooldown
      •  Temperature
          • Heatbed temperature
          • Nozzle temperature
          • Print Fan speed
          • Cooldown
      • Auto home
      • Set ready
      • Sheet profile
      • Disable Motors
      • Loading Test (Only Available when MMU is installed)
          • Test Filament 1
          • Test Filament 2
          • Test Filament 3
          • Test Filament 4
          • Test Filament 5
      • Live Adjust Z
      • Mesh Bed leveling
      • Bed level correction
          • Left Side
          • Right Side
          • Front Side
          • Rear Side
          • Reset
      • Calibrations & tests
          • 1. Fan test
          • 2. XY axis test
          • 3. Z alignment calibration
          • 4. Z axis test
          • 5. Heater test
          • 6. First Layer Calibration
  • Settings
      • Filament Sensor
      • MMU unit
      • Cutter (Only Available when MMU is installed)
      • Stealth Mode
      • Fan check
      • Verify GCode
      • Input shaper
          • Calibration
          • X-axis filter
          • X-axis frequency
          • Y-axis filter
          • Y-axis frequency
          • Restore defaults
      • User Interface
          • Footer
          • Sort Files [Time/Name]
          • Print Progress Screen [OFF, 30 s - 200 s]
          • Menu Timeout
          • Sound Mode [Loud/Silent/Assist/Once]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • RGB Status Bar
          • Touch
          • Touch Sig workaround
      • Language and Time
          • Language
              • English
              • Čeština
              • Deutsch
              • Español
              • Français
              • Italiano
              • Polski
              • ニホンゴ
          • Time Zone Hour Offset
          • Time Zone Minute Offset
          • Time Zone Summertime
          • Time Format
      • Network
          • Active Interface [Eth/Wi-fi]
          • Network status
              • Wi-fi status
              • IPv4 Address
              • IPv4 Gateway
              • MAC Address
              • Hostname
              • DNS Server
              • Connect Host
              • Connect IP
              • Ping | Loss
                • Connect
                • Gateway
                • DNS server
          • Wi-Fi
              • Wi-Fi status
              • SSID
              • Wi-Fi Wizard
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
          • Ethernet
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
          • Prusa Connect
              • Enabled
              • Status
              • Error
              • Hostname
              • Add printer to Connect
              • Load Settings
          • Prusa Link
              • Enabled
              • User
              • Password
              • IPv4 address
              • Hostname
              • Generate Password
          • Metrics & Log
              • What is this?
              • Allow
              • Enable Stored on Startup
              • Stored configuration
                • Host
                • Metrics port
                • Log Port
              • Current configuration
                • Metrics Host
                • Metrics Port
                • Log Host
                • Log Port
      • Hardware
          • Printer Type [MK3.5/MK3.5S]
          • Nozzle Diameter [0.40 mm/0.60 mm/0.80 mm/0.25 mm]
          • G-code checks
              • Nozzle Diameter [Warn/Strict/None]
              • Printer Model [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-code Level [Warn/Strict/None]
              • MK3 Compatibility [Warn/Strict/None]
              • Fan Compatibility [Warn/Strict/None]
          • Hotend Type [Stock/With Sock/Revo]
          • Filament Autoloading
          • Steel Sheets
      • FW update
      • System
          • Save Crash Dump
          • Device Hash in QR
          • Load Settings from File
          • Factory Reset
              • Reset Settings & Calibrations
              • Hard Reset (USB with FW needed)
  • Info
      • Network Status
          • Wi-Fi Status
          • IPv4 Address
          • IPv4 Gateway
          • MAC Address
          • Hostname
          • DNS Server
          • Connect Host 
          • Connect IP
          • Ping | Loss
            • Connect
            • Gateway
            • DNS Server
      • Sensor Info
          • Heatbreak Temp
          • Board Temperature
          • Bed Temperature
          • MCU temperature
          • Nozzle Temperature
          • P.I.N.D.A.
          • Filament Sensor
          • FINDA (Only Available when MMU is installed)
          • Print Fan
          • Hotend Fan
          • Heater Voltage
          • Input Voltage
          • Heater Current
          • Input Current
          • MMU current
      • Version Info
          • Firmware Version
          • Bootloader version
          • MMU Version (Only Available when MMU is installed)
          • Buddy board
          • Serial Number
          • Love Board
          • xLCD
      • Print Statistics
          • Fail Stats
              • Power failures
              • Load Fails in Print (Only Available when MMU is installed)
              • Total Load Fails (Only Available when MMU is installed)
              • General Fails in Print (Only Available when MMU is installed)
              • Total general Fails (Only Available when MMU is installed)
          • Statistics
              • X Axis
              • Y Axis
              • Z Axis
              • Filament
              • MMU filament loads
              • Print Time

Questo articolo è stato utile?

Commenti

Hai ancora delle domande?

Hai ancora delle domande?

Se hai una domanda su qualcosa che non è trattato qui, dai un'occhiata alle nostre risorse aggiuntive.
E se questo non dovesse funzionare, è possibile inviare una richiesta a [email protected] o tramite il pulsante qui sotto.

Contattaci