JA
  • English
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Mechanical lock (add-on)

Menu

Mechanical lock (add-on)

Mechanical lock (add-on)
Relevant for:
MINI+
Last updated 6 months ago
Mechanical lock (add-on)
 Difficulty
Easy
 Steps
11
 Available languages
ENCSPLDEITFR

Step 1 Introduction

Introduction
Introduction
⬢This guide will take you through the installation of the Mechanical lock on the Original Prusa MINI Enclosure.
The supplied fasteners contain extra spare parts.

Step 3 Additional tools

Additional tools
Additional tools
付属していないが、特にアドオンを取り付ける際に組み立てを容易にする工具。
⬢Additional tools:
⬢Needle-nose pliers for securing the E-clip washer

Step 4 Disassembling the door handle

Disassembling the door handle
Disassembling the door handle
Disassembling the door handle
⬢Open the door.
⬢On the door panel, remove two M3x8 screws securing the door-handle and remove it from the panel. Don't throw the screws away!
⬢Nice, we are ready to assembly the mechanical lock.

Step 5 Mechanical lock: parts preparation

Mechanical lock: parts preparation
Mechanical lock: parts preparation
Mechanical lock: parts preparation
Mechanical lock: parts preparation
⬢For the following steps, please prepare:
⬢M3x8 screw (2x) removed in the previous step
⬢MINI Enclosure Door Handle (1x)
⬢Magnet 20x6x2 (2x)
Keep the magnets apart in a sufficient distance. They can break each other!
⬢Lock housing nut (1x)
⬢Lock housing (1x)
⬢Lock wrench (1x)

Step 6 Assembling the lock housing

Assembling the lock housing
Assembling the lock housing
Assembling the lock housing
⬢Insert two magnets all the way into two pockets in the door handle.
The polarity of the magnets doesn't matter.
⬢Turn the door handle.
⬢Insert the lock housing into the same shape opening in the door handle.

Step 7 Securing the lock housing

Securing the lock housing
Securing the lock housing
Securing the lock housing
Securing the lock housing
⬢From the opposite side:
⬢Insert the nut onto the lock housing.
⬢Secure the lock housing by tightening the lock housing nut. Use the lock wrench for easier tightening.
⬢Attach the door handle on the door panel and secure it with two M3x8 screws.

Step 9 Assembling the lock mechanism

Assembling the lock mechanism
Assembling the lock mechanism
Assembling the lock mechanism
⬢Insert the Lock into the lock mount.
⬢Hold the Lock in the Lock mount with your hand and turn the door panel.
⬢Attach the mechanical Lock Lever to the Lock as shown in the picture. The lock lever must face upwards.

Step 10 Securing the lock mechanism

Securing the lock mechanism
Securing the lock mechanism
Securing the lock mechanism
Securing the lock mechanism
⬢Place E-clip washer on the Mechanical Lock Lever against the lock.
⬢Using Needle-nose pliers, push the E-clip washer on the lock to secure the lock mechanism.
⬢The Mechanical Lock is ready. Compare the picture with your Mechanical Lock.

Step 11 Good job!

Good job!
Good job!
⬢Perfect! You just successfully assembled the Mechanical lock on your Original Prusa MINI Enclosure. Let's try it out!
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us