⬢Versions of the MK3S manual:
⬢02/2019 - Initial version 3.10
⬢03/2019 - Updated to version 3.11
⬢07/2019 - Updated to version 3.12
⬢09/2019 - Updated to version 3.13
⬢06/2020 - Updated to version 3.14
⬢07/2020 - Updated to version 3.15
EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- 日本語
- Home
- MK3S
- Assembly manuals
- Original Prusa i3 MK3S kit assembly
- Manual changelog
Manual changelog
Menu
- Original Prusa i3 MK3S kit assembly
- 1. Introduction
- 2. Y-axis assembly
- 3. X-axis assembly
- 4. Z-axis assembly
- 5. E-axis assembly
- 6. LCD assembly
- 7. Heatbed & PSU assembly (Black PSU)
- 7. Heatbed & PSU assembly (Silver PSU)
- 8. Electronics assembly
- 9. Preflight check
- Manual changelog
- 1. Versions history
- 2. Changes to the manual (1)
- 3. Changes to the manual (2)
- 4. Changes to the manual (3)
- 5. Changes to the manual (4)
- 6. Changes to the manual (4)
- 7. Changes to the manual (5)
Manual changelog
Relevant for:
Last updated 4 years ago Difficulty
Moderate Steps
7 Available languages
⬢03/2019 - Chapter 2 (Y-axis)
⬢PSU holders assembly now depends on the type of the PSU, which is in your kit.
⬢03/2019 - Chapter 7 (HB & PSU)
⬢Chapter 7 is now in two versions depending on the PSU type, which is in your kit.
New PSU is fully black, old PSU has silver casing.
Manual version 3.11
⬢05/2019 - Chapter 7 (HB & PSU)
⬢Heatbed-cable-cover design improved to prevent collision with the extruder cables, which sometimes occurred. All screws are now facing down.
⬢New design with circular holes in the top part. The smaller part has hexagonal holes.
⬢Old design with hexagonal holes in the top part. The smaller part has circular holes.
Manual version 3.11
⬢07/2019 - Chapter 1 (Introduction)
⬢The printer's package contains a lubricant, which is intended for maintenance. No need to use it now the bearings are lubricated. There is a dedicated online manual on how to clean the printer and apply the lubricant. See Maintenance tips
⬢Several tweaks and new photos across the entire manual.
Manual version 3.12
⬢09/2019 - Chapter 1 (Introduction)
⬢Added warning about the ESD protection. Keep the electronics in the bag until needed for the assembly.
⬢09/2019 - Chapter 5 (Extruder)
⬢There is a new hardware revision of the IR-sensor with some optimisations. Filament detection is the same.
Manual version 3.13
⬢06/2020 - Chapter 2 (Y-axis assembly)
⬢New photos across the chapter show the position of PSU holders M3nE for Black PSU.
⬢06/2020 - Chapter 5 (E-axis assembly)
⬢FS-cover assembly step is moved a few steps earlier to prevent the IR-sensor from being damaged during assembly.
⬢06/2020 - Chapter 8 (Electronics assembly)
⬢New photos in this chapter include cable guiding from the Black PSU.
Manual version 3.14
⬢07/2020 - Chapter 2 (Y-axis assembly)
⬢The correct orientation of the bearings on the Y-carriage has been adjusted.
⬢The correct orientation, the tracks (rows of the balls) are on the sides.
⬢The incorrect orientation, the track is in the middle of the hole.
⬢
The printed version of this manual (v3.14 and older) suggests a different approach, please follow the online version instead.
⬢Added instructions, how to glue the silver label on the frame.
Manual version 3.15
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.