⬢This guide will take you through the installation of the Fire Suppression System into the Original Prusa Enclosure.
EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Enclosure
- Assembly manuals
- Original Prusa Enclosure assembly (external display mounting)
- 5. Fire Suppression System (add-on)
5. Fire Suppression System (add-on)
Menu
- Original Prusa Enclosure assembly (external display mounting)
- 1. Introduction
- 2A. Preparing the printer (MK4/S & 3.9/S)
- 2B. Preparing the printer (MK3S+ Black PSU)
- 2C. Preparing the printer (MK3S+ Silver PSU)
- 3. Assembling the enclosure
- 4A. Installing the printer (MK4/S & 3.9/S)
- 4B. Installing the printer (MK3S+ Black PSU)
- 4C. Installing the printer (MK3S+ Silver PSU)
- Manual changelog Enclosure kit
- 5. Fire Suppression System (add-on)
- 1. Introduction
- 2. Tools necessary for this guide
- 3. Preparing the printer
- 4. Parts preparation:
- 5. Mounting the P-clamp
- 6. Mounting the P-clamp
- 7. Installing the automatic suppression system
- 8. Securing the automatic suppression system
- 9. That's it!
- 6. Hinged Lid (add-on)
- 6A. Hinged Lid with MMU3
- 6B. Hinged lid with MMU2S
- 7. Advanced filtration system (add-on)
- 8. Mechanical lock (add-on)
- 9. Quick release PSU cable - MK3S+ Black PSU (add-on)
- 10. Quick release PSU cable - MK4/3.9 Black PSU (add-on)
- 11. White LED strip (add-on)
5. Fire Suppression System (add-on)
Relevant for:
Last updated 2 years ago Difficulty
Easy Steps
9 Available languages
⬢For this guide, please prepare:
⬢2.5mm Allen key
⬢Piece of cloth or fabric (at least 20x20 cm) for covering the heatbed
Make sure the printer is turned OFF and cool down!
Before you proceed, it is recommended to protect the heatbed.
⬢Take off the flexible steel sheet.
⬢Use any cloth or piece of fabric, which is thick enough and cover the heatbed. This will ensure you won't damage (scratch) the surface during the disassembly.
⬢For the following steps, please prepare:
⬢P-clamp (2x)
⬢M3 nut assembly (2x) the nut with the M3x12 screw
⬢Fire suppression system tube (1x) type: T033E BlazeCut T Series Fire Suppression 1 System with a pressure gauge
Handle the tube carefully to avoid damage.
⬢Unscrew both M3x12 screws from the nuts.
⬢Locate two holes (the two farther apart) on the rear side of the top panel and insert the M3x12 screws into both holes.
⬢From the inside, locate the inserted M3x12 screws on the right side of the top panel.
⬢Insert the nut into the P-clamp. See the correct orientation of both parts.
⬢Attach the nut in the P-clamp to the M3x12 screw in the top panel. Tighten the screw using the Allen key from the top with your other hand. Do not tighten the screw now! A few turns are enough. We will tighten it later.
⬢Insert the metal end of the tube into the P-clamp.
If it is difficult to insert the tube into the P-clamp, loosen the nut a little. But be careful not to drop the P-clamp!
⬢Make sure the nut is accessible from the front.
⬢From the other side of the tube, slide the second P-clamp on the metal part of the tube. Mind the correct position of the P-clamp.
⬢Insert the nut into the P-clamp and attach it to the M3x12 screw on the left. Slightly tighten the screw using the Allen key from the top with your other hand - a few turns are enough for now. We will completely tighten it later.
⬢Align the tube in the P-clamps. There should be an equal piece of tube section protruding out on each side.
⬢Fully tighten the P-clamps.
⬢Congratulations! You just successfully installed the Fire Suppression System.
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.