ES
  • English
  • Italiano
Iniciar sesión

How to replace the main cable connector cover (XL)

Menu

How to replace the main cable connector cover (XL)

How to replace the main cable connector cover (XL)
Relevante para :
XL
Ultima actualización 8 hours ago
How to replace the main cable connector cover (XL)
 Dificultad
Moderada
 Pasos
38
 Idiomas disponibles
ENIT

Paso 1 Introduction

Introduction
Introduction
Introduction
⬢This guide will take you through the installation of the Main cable connector cover on the Original Prusa XL.
The following instructions are compatible with Original Prusa XL Multi-Tool and Single-Tool.
⬢Todas las piezas necesarias están disponibles en nuestra tienda prusa3d.com.
⬢This manual is compatible with the Original Prusa XL Enclosure.
We will demonstrate replacing the Main cable connector cover on a printer without the XL Enclosure for better visibility. There is no need to remove the XL Enclosure.
Do not discard any removed parts unless prompted to do so.

Paso 2 Tools necessary for this manual

Tools necessary for this manual
Tools necessary for this manual
Tools necessary for this manual
⬢For the following manual, please prepare:
⬢Torx T10 screwdriver
⬢Llave Allen de 2.5 mm
⬢A cardboard box for use as heatbed protection during the assembly. We will use the Nextruder box as an example.

Paso 3 Unloading the filament

Unloading the filament
Unloading the filament
Unloading the filament
Unloading the filament
⬢If you have loaded the filament, unload it from the hotend. On the screen, navigate to Filament -> Unload Filament.
⬢Retira el filamento del hotend. Es necesario retirarlo completamente de la impresora.
ADVERTENCIA: El hotend y la base calefactable están muy CALIENTES. ¡No toques estas piezas!
⬢Mueva el eje Z abajo. En la pantalla, navega hasta Control -> Mover Eje -> Mover Z.
⬢Enfría la impresora. En la pantalla, ve a Precalentar -> Enfriar.
Espera a que las piezas calientes se enfríen a temperatura ambiente. Tarda aproximadamente 10 minutos.

Paso 4 Unpluging the printer

Unpluging the printer
Unpluging the printer
⬢Apaga el interruptor (símbolo "O").
⬢Desde la parte posterior de la impresora, desenchufa el cable de la fuente de alimentación.

Paso 5 Protecting the heatbed

Protecting the heatbed
Protecting the heatbed
Antes de continuar, te recomendamos que protejas la base calefactable.
⬢Asegúrate de que la base calefactable se enfría a temperatura ambiente. Coloca la caja de cartón vacía aproximadamente en la parte delantera central de la base calefactable.

Paso 6 Multi-Tool & Single-Tool

Multi-Tool & Single-Tool
Multi-Tool & Single-Tool
Multi-Tool & Single-Tool
The following instructions are divided according to your printer variant. 
⬢Choose the appropriate steps:
⬢Multi-Tool: please proceed to the next step
⬢Single-Tool: please proceed to the Single-Tool: releasing the Nextruder
Some steps are demonstrated using the Multi-Tool variant, but the procedure remains the same for both the Multi-Tool and Single-Tool variants.

Paso 7 Multi-Tool: disconnecting the Nextruder

Multi-Tool: disconnecting the Nextruder
Multi-Tool: disconnecting the Nextruder
Multi-Tool: disconnecting the Nextruder
Multi-Tool: disconnecting the Nextruder
⬢Desde la parte frontal del Nextruder, utilizando un destornillador T10, afloja (unas pocas vueltas son suficientes) dos tornillos M3x8r y retira el soporte del cable.
⬢Locate the fitting, press the blue collet and unplug the PTFE tube from the Nextruder. Leave the PTFE hanging freely.
⬢Locate the Nextruder cable, press the secure latch and unplug the cable from the second Nextruder. Leave the cable hanging.

Paso 8 Multi-Tool: Disassembling the Nextruder cable

Multi-Tool: Disassembling the Nextruder cable
Multi-Tool: Disassembling the Nextruder cable
Multi-Tool: Disassembling the Nextruder cable
Multi-Tool: Disassembling the Nextruder cable
⬢Put the Nextruder cable on the box.
⬢Using a 2.5 mm Allen key, remove the M3x16 screw from the xl-dwarf-cover-connector.
⬢Gently remove the Nextruder cable from the xl-dwarf-cover-connector. Discard the xl-dwarf-cover-connector, as it is no longer needed. 

Paso 10 Multi-Tool: Preparing the XL dwarf cover connector

Multi-Tool: Preparing the XL dwarf cover connector
Multi-Tool: Preparing the XL dwarf cover connector
Multi-Tool: Preparing the XL dwarf cover connector
Multi-Tool: Preparing the XL dwarf cover connector
⬢Take the XL-dwarf-cover-connector.
Proceed carefully, do not break the XL-dwarf-cover-connector!
⬢Use both hands to gently open the XL-dwarf-cover-connector. An opening of 5.0 mm is sufficient.
⬢Insert the M3nN nut into the prepared hexagon hole in the XL-dwarf-cover-connector.

Paso 11 Multi-Tool: Reassembling the Nextruder cable

Multi-Tool: Reassembling the Nextruder cable
Multi-Tool: Reassembling the Nextruder cable
Multi-Tool: Reassembling the Nextruder cable
Multi-Tool: Reassembling the Nextruder cable
⬢Insert the Nextruder cable into the prepared XL-dwarf-cover-connector.
⬢Insert the XL-dwarf-cover-connector into the XL-dwarf-cover-connector-jig.
¡No pellizques ningún cable!
The Nextruder cable needs to be longer than the front of the XL-dwarf-cover-connector-jig.
⬢Insert the M3x10 screw and secure it with a 2.5 mm Allen key.

Paso 13 Multi-Tool: Disassembling the Nextruder

Multi-Tool: Disassembling the Nextruder
Multi-Tool: Disassembling the Nextruder
Multi-Tool: Disassembling the Nextruder
Multi-Tool: Disassembling the Nextruder
The next steps are compatible with both Single-tool and Multi-tool Nextruders.
⬢Using a 2.5 mm Allen key, remove the M3x16 screw.
⬢Remove the XL-dwarf-cover-door.
⬢Turn the Nextruder so that the back is facing upwards.
⬢Using a T10 Torx screwdriver, remove two M3x6bT screws.
⬢Remove the XL-dwarf-cover-back.
⬢Slide the XL-dwarf-cover-base off the dwarf board and discard it, as it is no longer needed.

Paso 15 Multi-Tool: Preparing the XL dwarf cover base

Multi-Tool: Preparing the XL dwarf cover base
Multi-Tool: Preparing the XL dwarf cover base
Multi-Tool: Preparing the XL dwarf cover base
Multi-Tool: Preparing the XL dwarf cover base
⬢Insert two M3nS nuts into the holes.
⬢Ensure the screw holes in the printed part align with the nuts.
⬢Insert two M3nS nuts into the holes.
⬢Insert the M3nN nut into the hole.

Paso 16 Multi-Tool: Securing the XL dwarf cover base

Multi-Tool: Securing the XL dwarf cover base
Multi-Tool: Securing the XL dwarf cover base
Multi-Tool: Securing the XL dwarf cover base
Multi-Tool: Securing the XL dwarf cover base
⬢There is a rail on each inner side of the part. These rails are meant to slide onto the Dwarf board.
⬢Push the XL-dwarf-cover-base onto the Dwarf board and slide it into place.
⬢Place the XL-dwarf-cover-back onto the assembly.
⬢Insert two M3x6bT screws and secure them with a T10 Torx screwdriver.

Paso 19 Multi-Tool: docking the Nextruder

Multi-Tool: docking the Nextruder
Multi-Tool: docking the Nextruder
Multi-Tool: docking the Nextruder
Multi-Tool: docking the Nextruder
⬢Coloca los dos pines metálicos a través de los orificios blancos del dock. Los imanes te ayudarán a acoplar el Nextruder.
Check that the cable bundle is not twisted!
⬢Engancha los orificios de la placa flexible del haz de cables en las cabezas de los tornillos y empujalos a la posición correcta.
⬢Tighten two M3x8rT screws. using a T10 Torx screwdriver.

Paso 20 Multi-Tool: securing the cable bundle

Multi-Tool: securing the cable bundle
Multi-Tool: securing the cable bundle
Multi-Tool: securing the cable bundle
Multi-Tool: securing the cable bundle
⬢Insert the PTFE tube into the fitting on the Nextruder. Push it all the way in.
⬢Attach the Nextruder cable to the top of the Nextruder and connect the main cable to the slot on the Dwarf board.
⬢Insert two M3x10 screws and secure them using a 2.5 mm Allen key.
⬢Proceed the same to the remaining tools.
⬢When all the remaining tools are finished, proceed to the Good job

Paso 21 Single-Tool: releasing the Nextruder

Single-Tool: releasing the Nextruder
Single-Tool: releasing the Nextruder
Single-Tool: releasing the Nextruder
⬢This is where Single-tool assembly begins.
⬢Gire la impresora de modo que la parte frontal quede orientada hacia ti.
⬢Retire la x-carriage-cover del carro X. No lo tires, ¡lo usaremos más tarde!
⬢Con una llave Torx T10, retira dos tornillos M3x12bT.

Paso 22 Single-Tool: detaching the Nextruder

Single-Tool: detaching the Nextruder
Single-Tool: detaching the Nextruder
Single-Tool: detaching the Nextruder
⬢Sujeta el Nextruder durante el desmontaje.
⬢Untighten two M3x12bT screws using a T10 Torx key.
⬢Detach the Nextruder and place it nearby, we will rebuilt it in the next steps.
⬢Place the Nextruder with the cable bundle on the box.

Paso 23 Single-Tool: releasing the cable bundle

Single-Tool: releasing the cable bundle
Single-Tool: releasing the cable bundle
Single-Tool: releasing the cable bundle
Single-Tool: releasing the cable bundle
⬢Desde la parte frontal del Nextruder, utilizando un destornillador Torx T10 afloja dos tornillos y retira el soporte del cable.
⬢Press the fitting and pull out the PTFE tube.
⬢Presiona la pestaña de seguridad y retira el cable del Nextruder.
⬢Put the Nextruder aside, we will work on it later.

Paso 24 Single-Tool: Disassembling the Nextruder cable

Single-Tool: Disassembling the Nextruder cable
Single-Tool: Disassembling the Nextruder cable
Single-Tool: Disassembling the Nextruder cable
Single-Tool: Disassembling the Nextruder cable
⬢Put the Nextruder cable on the box.
⬢Using a 2.5 mm Allen key, remove the M3x16 screw from the xl-dwarf-cover-connector.
⬢Gently remove the Nextruder cable from the xl-dwarf-cover-connector. Discard the xl-dwarf-cover-connector, as it is no longer needed.

Paso 26 Single-Tool: Preparing the XL dwarf cover connector

Single-Tool: Preparing the XL dwarf cover connector
Single-Tool: Preparing the XL dwarf cover connector
Single-Tool: Preparing the XL dwarf cover connector
Single-Tool: Preparing the XL dwarf cover connector
⬢Take the XL-dwarf-cover-connector.
⬢Using both hands, gently open the XL-dwarf-cover connector. Open it just enough—5.0 mm is sufficient.
Proceed carefully, do not break the XL-dwarf-cover-connector!
⬢Insert the M3nN nut into the prepared hexagon hole in the XL-dwarf-cover-connector.

Paso 27 Single-Tool: Reassembling the Nextruder cable

Single-Tool: Reassembling the Nextruder cable
Single-Tool: Reassembling the Nextruder cable
Single-Tool: Reassembling the Nextruder cable
Single-Tool: Reassembling the Nextruder cable
⬢Insert the Nextruder cable into the prepared XL-dwarf-cover-connector.
⬢Insert the XL-dwarf-cover-connector into the XL-dwarf-cover-connector-jig.
¡No pellizques ningún cable!
The Nextruder cable must extend beyond the front of the XL-dwarf-cover-connector-jig.
⬢Insert the M3x10 screw and secure it with a 2.5 mm Allen key.

Paso 28 Single-Tool: Disassembling the Nextruder

Single-Tool: Disassembling the Nextruder
Single-Tool: Disassembling the Nextruder
Single-Tool: Disassembling the Nextruder
Single-Tool: Disassembling the Nextruder
⬢Using a 2.5 mm Allen key, remove the M3x16 screw. Don't throw the part away!
⬢Remove the XL-dwarf-cover-door. Don't throw the part away!
⬢Turn the Nextruder so that the back is facing upwards.
⬢Using a T10 Torx screwdriver, remove two M3x6bT screws. Don't throw the parts away!
⬢Remove the XL-dwarf-cover-back. Don't throw the part away!
⬢Slide out the XL-dwarf-cover-base from the dwarf board. Throw the XL-dwarf-cover-base away.

Paso 31 Single-Tool: Securing the XL dwarf cover base

Single-Tool: Securing the XL dwarf cover base
Single-Tool: Securing the XL dwarf cover base
Single-Tool: Securing the XL dwarf cover base
Single-Tool: Securing the XL dwarf cover base
⬢There is a rail on each inner side of the part. These rails are meant to slide onto the Dwarf board.
⬢Push the XL-dwarf-cover-base to the dwarf board and slide it in place.
⬢Place the XL-dwarf-cover-back onto the assembly.
⬢Insert two M3x6bT screws and secure them with a T10 Torx screwdriver.

Paso 34 Single-Tool: securing the Nextruder cable

Single-Tool: securing the Nextruder cable
Single-Tool: securing the Nextruder cable
Single-Tool: securing the Nextruder cable
⬢Attach the Nextruder cable to the top of the Nextruder and connect the main cable to the slot on the Dwarf board.
⬢Insert two M3x10 screws and secure them using a 2.5 mm Allen key.

Paso 35 Single-Tool: securing the cable bundle

Single-Tool: securing the cable bundle
Single-Tool: securing the cable bundle
Single-Tool: securing the cable bundle
⬢Insert the PTFE tube into the fitting on the Nextruder. Push it all the way in.
⬢Hook up the keyhole openings in the flexible plate of the cable bundle and tighten two M3x8rT screws using a T10 Torx screwdriver.

Paso 37 Single-Tool: installing the Nextruder

Single-Tool: installing the Nextruder
Single-Tool: installing the Nextruder
Single-Tool: installing the Nextruder
Single-Tool: installing the Nextruder
⬢Desde la parte posterior del carro X, fija el conjunto del extrusor al carro X. Observa la orientación correcta del extrusor.
⬢Insert and fully tighten all four M3x12bT screws diagonally to secure the extruder assembly.
⬢Attach the bottom part of the x-carriage-cover back onto the X-carriage, then snap the upper part onto the X-carriage. You must feel a slight "click" to ensure the cover fits on the part.

Paso 38 Good job

Good job
Good job
Good job
⬢Well done! The XL-dwarf-cover-connector is replaced.
¿Fue útil esta guía?

Comentarios

¿Todavía tienes preguntas?

¿Todavía tienes preguntas?

Si tienes alguna pregunta sobre algo que no se ha tratado aquí, comprueba nuestros recursos adicionales.
Y si eso no lo soluciona, puedes enviar una petición a [email protected] o mediante el botón que hay más abajo.

Contacta con nosotros