English
Deutsch
Français

LCD menu (MK3.5/S)

Relevante para :

Ultima actualización 6 days ago

Este artículo está también disponible en los siguientes idiomas:

The Original Prusa MK3.5S is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Make sure always to have the latest firmware.

Tune
- - Live Adjust Z
  - Change Filament
  - Cancel Object
    - - Cancel Current
  - Print Speed
  - Nozzle Temperature
  - Heatbed Temperature
  - Print Fan Speed
  - Flow Factor
  - Filament Sensor
  - Stealth Mode
  - Sound Mode [Loud/Silent/Assist/Once]
  - Input Shaper
    - - Calibration
      - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore defaults
  - Fan Check
  - Verify Gcode
  - Cutter (Only Available when MMU is installed)
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - RGB Status Bar
      - Touch
      - Touch Sig workaround
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        Wi-fi status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Connect Host
        
        Connect IP
        
        Ping | Loss
        
        Connect
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Allow
        
        Enable Stored on Startup
        
        Stored configuration
        
        Host
        
        Metrics port
        
        Log Port
        
        Current configuration
        
        Metrics Host
        
        Metrics Port
        
        Log Host
        
        Log Port
  - Time Zone Hour Offset
  - Time Zone Minute Offset
  - Time Zone Summertime
  - Info
  - Message History
Pause
Stop

Print
Preheat
- - PLA
  - PETG
  - ASA
  - PC
  - PVB
  - ABS
  - HIPS
  - PP
  - FLEX
  - PA
  - Cooldown
Filament
- - Load filament
  - Unload filament
  - Change filament
  - Purge filament
  - Preload to MMU (Only Available when MMU is installed)
    - - Preload All
      - Preload Filament 1
      - Preload Filament 2
      - Preload Filament 3
      - Preload Filament 4
      - Preload Filament 5
  - Preload to MMU Advanced (Only Available when MMU is installed)
    - - Filament 1 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
      - Filament 2 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
      - Filament 3 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
      - Filament 4 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
      - Filament 5 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
      - Carry Out the Changes
  - Load to Nozzle (Only Available when MMU is installed)
    - - Load Filament 1
      - Load Filament 2
      - Load Filament 3
      - Load Filament 4
      - Load Filament 5
  - Unload Filament (Only Available when MMU is installed)
    - - PLA
      - PETG
      - ASA
      - PC
      - PVB
      - ABS
      - HIPS
      - PP
      - FLEX
      - PA
  - Eject From MMU (Only Available when MMU is installed)
    - - Eject From MMU 1
      - Eject From MMU 2
      - Eject From MMU 3
      - Eject From MMU 4
      - Eject From MMU 5
  - Cut Filament (Only Available when MMU is installed)
    - - Cut Filament 1
      - Cut Filament 2
      - Cut Filament 3
      - Cut Filament 4
      - Cut Filament 5
      - Manage Filaments (Only Available when MMU is installed)
Control
- - Move axis
    - - Move X
      - Move Y
      - Move Z
      - Move E
      - Cooldown
  - Temperature
    - - Heatbed temperature
      - Nozzle temperature
      - Print Fan speed
      - Cooldown
  - Auto home
  - Set ready
  - Sheet profile
  - Disable Motors
  - Loading Test (Only Available when MMU is installed)
    - - Test Filament 1
      - Test Filament 2
      - Test Filament 3
      - Test Filament 4
      - Test Filament 5
  - Live Adjust Z
  - Mesh Bed leveling
  - Bed level correction
    - - Left Side
      - Right Side
      - Front Side
      - Rear Side
      - Reset
  - Calibrations & tests
    - - 1. Fan test
      - 2. XY axis test
      - 3. Z alignment calibration
      - 4. Z axis test
      - 5. Heater test
      - 6. First Layer Calibration
Settings
- - Filament Sensor
  - MMU unit
  - Cutter (Only Available when MMU is installed)
  - Stealth Mode
  - Fan check
  - Verify GCode
  - Input shaper
    - - Calibration
      - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore defaults
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - RGB Status Bar
      - Touch
      - Touch Sig workaround
  - Language and Time
    - - Language
        
        English
        
        Čeština
        
        Deutsch
        
        Español
        
        Français
        
        Italiano
        
        Polski
        
        ニホンゴ
      - Time Zone Hour Offset
      - Time Zone Minute Offset
      - Time Zone Summertime
      - Time Format
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        Wi-fi status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Connect Host
        
        Connect IP
        
        Ping | Loss
        
        Connect
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Allow
        
        Enable Stored on Startup
        
        Stored configuration
        
        Host
        
        Metrics port
        
        Log Port
        
        Current configuration
        
        Metrics Host
        
        Metrics Port
        
        Log Host
        
        Log Port
  - Hardware
    - - Printer Type [MK3.5/MK3.5S]
      - Nozzle Diameter [0.40 mm/0.60 mm/0.80 mm/0.25 mm]
      - G-code checks
        
        Nozzle Diameter [Warn/Strict/None]
        
        Printer Model [Warn/Strict/None]
        
        Firmware Version [Warn/Strict/None]
        
        G-code Level [Warn/Strict/None]
        
        MK3 Compatibility [Warn/Strict/None]
        
        Fan Compatibility [Warn/Strict/None]
      - Hotend Type [Stock/With Sock/Revo]
      - Filament Autoloading
      - Steel Sheets
  - FW update
  - System
    - - Save Crash Dump
      - Device Hash in QR
      - Load Settings from File
      - Factory Reset
        
        Reset Settings & Calibrations
        
        Hard Reset (USB with FW needed)
Info
- - Network Status
    - - Wi-Fi Status
      - IPv4 Address
      - IPv4 Gateway
      - MAC Address
      - Hostname
      - DNS Server
      - Connect Host
      - Connect IP
      - Ping | Loss
        
        Connect
        
        Gateway
        
        DNS Server
  - Sensor Info
    - - Heatbreak Temp
      - Board Temperature
      - Bed Temperature
      - MCU temperature
      - Nozzle Temperature
      - P.I.N.D.A.
      - Filament Sensor
      - FINDA (Only Available when MMU is installed)
      - Print Fan
      - Hotend Fan
      - Heater Voltage
      - Input Voltage
      - Heater Current
      - Input Current
      - MMU current
  - Version Info
    - - Firmware Version
      - Bootloader version
      - MMU Version (Only Available when MMU is installed)
      - Buddy board
      - Serial Number
      - Love Board
      - xLCD
  - Print Statistics
    - - Fail Stats
        
        Power failures
        
        Load Fails in Print (Only Available when MMU is installed)
        
        Total Load Fails (Only Available when MMU is installed)
        
        General Fails in Print (Only Available when MMU is installed)
        
        Total general Fails (Only Available when MMU is installed)
      - Statistics
        
        X Axis
        
        Y Axis
        
        Z Axis
        
        Filament
        
        MMU filament loads
        
        Print Time

¿Fue útil este artículo?

Fácil de comprender

Resolvió mi problema

Otra razón

Comentarios

¿Todavía tienes preguntas?

Si tienes alguna pregunta sobre algo que no se ha tratado aquí, comprueba nuestros recursos adicionales.
Y si eso no lo soluciona, puedes enviar una petición a [email protected] o mediante el botón que hay más abajo.

Contacta con nosotros

LCD menu (MK3.5/S)

Menu structure during printing

Menu structure when idle

Comentarios

¿Todavía tienes preguntas?