⬢Pro tuto kapitolu si prosím připravte:
⬢2.5mm Allen key
CS
Přihlásit- English
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- CORE One
- Manuály k sestavení
- Prusa CORE One
- 3. Mounting the xLCD
3. Mounting the xLCD
Menu
- Prusa CORE One
- 1. Úvod
- 2. Unpacking the printer
- 3. Mounting the xLCD
- 1. Nářadí potřebné k této kapitole
- 2. Removing the bezel
- 3. Montáž xLCD: příprava dílů
- 4. Připojení sestavy xLCD
- 5. Mounting the xLCD
- 6. Attaching the display assembly
- 7. Peeling off the protectives
- 4. Kalibrace & První spuštění
- Manual changelog
3. Mounting the xLCD
Relevantní pro:
Poslední aktualizace 3 days ago Obtížnost
Nízká Kroky
7 Dostupné překlady
⬢Open the door fully.
⬢Lift the right end of the front bezel and unhook it from the printer frame.
⬢Pull the bezel out of the printer. Do not discard the part.
Proceed carefully to avoid scratching the parts or damaging the door.
The bezel is attached to the printer with magnets, making it easy to remove.
⬢Note the cables coming from the printer. We’ll address them shortly. Avoid pushing them into the printer, keep them as they are.
⬢Pro následující kroky si prosím připravte:
⬢xLCD assembly (1x)
⬢Connect the xLCD cable (gray cable with red connector) to the xLCD board on the back of the xLCD assembly. Do not pull on the cable!
Ensure the latch on the connector is positioned on the same side of the slot as the triangle symbol on the xLCD board. Otherwise, the xLCD won't work.
⬢Take the FE cable and fully slide the metal connector onto the FE Faston (brass connector) on the xLCD board. Do not pull on the cable!
For a better overview of the correct connection of both cables, see the illustrations.
⬢Install the bezel onto the screws on the back of the xLCD assembly.
⬢Ensure the magnets face upward. The bezel has four magnets, but only two are visible in the picture.
⬢Ensure both screws (M3x6) are not fully tightened, leaving approximately a 3 mm (1/8 inch) gap between the screw head and the xLCD cover.
⬢Slide the bezel toward you, ensuring both screws are positioned at the end of the keyhole-shaped holes.
⬢Keep the bezel in position and fully tighten both screws.
⬢Carefully install the display assembly (xLCD and bezel) onto the printer using the following procedure:
Proceed carefully to avoid scratching the parts or damaging the door.
⬢Hook the left side of the bezel onto the left frame of the printer, ensuring the square cutout is securely attached to the frame.
⬢Slowly lower the right side into place as well.
⬢Připevněte pravou stranu rámečku k pravému rámu tiskárny a ujistěte se, že je čtvercový výřez pevně spojen s rámem.
⬢Ensure the bezel is evenly seated at both ends along the bottom edge — test it by closing the door slowly to check if the bezel obstructs movement.
⬢Now, you can remove the protective films from the transparent panels on the printer.
⬢The protective film is located on the top, left, and right sides of the printer.
⬢We are almost there! Let's go to the last chapter: 4. Calibration & First run
Byl tento návod užitečný?
Komentáře
Stále nemáte jasno?
Pokud nemůžete najít odpověď na vaši otázku, projděte si naše další materiály na webu.
A pokud nenajdete odpověď, pošlete nám zprávu na [email protected] nebo přes tlačítko níže.