LCD menu

Navigating the LCD menu is done by a single control element: a rotational knob that you press to confirm a selection. In addition, you have a Reset button which will reset the printer if pushed. The main LCD screen also displays some other information about your printer's current state.

• Print
• Preheat
  • • • PLA
      • PETG
      • ASA
      • PC
      • PVB
      • ABS
      • HIPS
      • PP
      • FLEX
      • PA
      • Custom
        • • Name
          • Nozzle temperature
          • Nozzle Preheat Temperature
          • Bed Temperature
          • Is Abrasive
          • Requires Filtration
          • Confirm
      • Show All
      • Cooldown
• Filament
  • • • Load filament
      • Unload filament
      • Change filament
      • Purge filament
      • Manage Filaments
        • • Loaded
            • • Name
              • Visible
              • Nozzle temp
              • Preheat Temp
              • Bed Temp
              • Is Abrasive
              • Requires Filtration
          • Edit Filaments
          • Reorder Filaments
          • Enable Filaments
• Control
  • • • Move Axis
        • • Move X
          • Move Y
          • Move Z
          • Move E
          • Cooldown
      • Temperature
        • • Nozzle
          • Heatbed
          • Print Fan
          • Cooldown
      • Auto home
      • Set ready
      • Disable Motors
      • Live Adjust Z
      • Mesh Bed leveling
      • Bed level correction
        • • Left side
          • Right side
          • Front side
          • Rear side
          • Reset
      • Calibrations & Tests
        • • Fan Test
          • XY axis Test
          • Z axis Test
          • Heater Test
          • First Layer calibration
• Settings
  • • • Filament Sensor
      • Stealth Mode
      • Fan Check
      • Verify Gcode
      • Input Shaper
        • • X-axis filter
          • X-axis freq.
          • Y-axis filter
          • Y-axis freuq.
          • Restore Defaults
      • User Interface
        • • Footer
            • • Item 1 [None/Nozzle/Bed/Filament/FSensor/Speed/X/Y/Z/Z height/Print fan/Hotend fan/Live Z/Sheets/Nozzle dia/Nozzle PMW]
              • Item 2
              • Item 3
              • Reset
          • Sort Files [Time/Name]
          • Menu Timeout
          • Sound Mode [Silent/Assist/Once/Loud]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • Sound Volume [Off/0-11]
      • Language & Time
        • • Language
          • Time Zone Hour Offset
          • Time Zone Minute Offset
          • Time Zone Summertime
          • Time Format [24h/12h]
          • Time
      • Network
        • • Active Interface [Eth/Wi-Fi]
          • Network Status
            • • Status
              • IP
              • Gateway
              • MAC
              • Hostname
              • DNS
              • Ping | Loss
              • Gateway
              • DNS
          • Wi-Fi
            • • Status
              • DDID
              • Wi-Fi Wizard
              • Protocol
              • LAN
              • IP
              • Mask
              • Gateway
              • Hostname
              • MAC
          • Ethernet
            • • Protocol
              • LAN
              • IP
              • Mask
              • Gateway
              • Hostname
              • MAC
          • Prusa Connect
            • • Enabled
              • Status
              • Error
              • Hostname
              • Add Printer to Connect
              • Load Settings
          • Prusalink
            • • Enabled
              • User
              • Password
              • IP
              • Hostname
              • Generate password
          • Metrics & Log 
            • • What is this?
              • Enable Metrics
              • Host
              • Metrics Port
              • Syslog Port
              • MAC
              • Metrics List
      • Hardware
        • • Print head
            • • Nozzle Diameter
              • Nozzle hardened
              • Nozzle High-flow
          • Steel Sheets
          • G-code checks
            • • Nozzle [Warn/Strict/None]
              • Printer Model [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-code Level [Warn/Strict/None]
      • FW update
      • System
        • • Save Crash Dump
          • Save Logs To File
          • Device Hash in QR
          • Load Settings from File
          • Factory Reset
            • • Reset Settings & Calibrations
              • Hard Reset (USB with FW needed)
• Info
  • • • Network Status
        • • Status
          • IP
          • Gateway
          • MAC
          • Hostname
          • DNS
          • PING | Loss
          • Gateway
          • DNS
      • Sensor info
        • • Filament Sens
          • M.I.N.D.A.
          • MCU Temperature
      • Version info
        • • Firmware Version
          • Bootloader Version
          • Buddy Board
      • Print Statistics
        • • Statistics
            • • X Axis
              • Y Axis
              • Z Axis
              • Filament
              • Print Time