EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Calibration
- Calibration Error Messages
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
Menu
- Basic calibration
- Advanced calibration
- Calibration Error Messages
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- Check Axis Length X/Y/Z (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- Distance between tip of the nozzle and the bed surface has not been set yet
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- What happened?
- How to fix it?
- How to replace the part?
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- Printer has not been calibrated yet
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QR Error codes
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- Static memory has been overwritten
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- XYZ Calibration error-messages (MK2/S)
- XYZ-calibration error-messages (MK3/MK3S/MK3S+)
This article is also available in following languages: 
What happened?
The printer displaying the message: Internal error (DBUS mapping failed), please restart the printer. Contact the support if the problem persists.
Error name: Internal error (DBUS mapping failed)
Error code: #10507
This is triggered by a software bug, but there is a small probability it is a result of a hardware error.
How to fix it?
Do a factory reset of the printer and flash the firmware. If the problem persists, the A64 logic board must be replaced.
How to replace the part?
Was this article helpful?
Comments
Related
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.